ML 7R

Myford 2 MT Collets fit directly into the spindle of all ML10, Speed 10, Diamond 10, ML7, ML7-R and Super 7 lathes, with spindle nose bored 2 MT and threaded 1....

Myford Part No: 73/1112/1Length: 510 mm (20") for standard bed length lathesThis is the later type longer rack for power cross feed Super 7's but can be used as...

5/16" B.S.F hinge screws for Super 7 change gear guard; Super 7 motor drive belt guard & quick change gearbox end cover
Myford Part No. A2024
Quantity...

Myford Part No: A2123Screws that fit into the countershaft to adjust the headstock belt tensionQuantity: pack of 2Condition: NewApplication: ML7; ML-7R; Super 7...

Myford Part No: A2050 & A2051Clamp screw and head used to lock the motor platformApplication: Super 7; ML-7RCategory: New Items...

Myford Part No: 75/1115/1Thrust collar which fits on the leadscrew to bear against the R.H leadscrew support bracketApplication: ML7; ML-7R; Super 7Category: Ne...

Locking nuts to fit the tailstock clamping stud and to secure the tailstock handwheel
Thread: 3/8" B.S.F
Finish: Bright zinc plate
Unit Quantity: Pack ...

Locking nut used at the R.H end of the leadscrew
Fastener Type: Locking nut
Locking Method: Nylon insert
Thread: 7/16" B.S.F
Finish: Bright zinc pla...

Myford Part No: A3115 (11285/24)
24 tooth gear which fits to the tumbler sleeve gear on lathes fitted with a quick change gearbox
Condition: New
Appli...

Replacement oil nipples used throughout Myford lathesFlat front face and spherical rear form permits use with all types of push fit oil guns These nipples have ...

Myford reference: Woodruf Key No. 404Used throughout Myford lathesSize: ½" x ⅛"Quantity: Pack of 5Application: ML7; ML-7R; ML10; Super 7Category: New_Item...

Myford Part No: A3021Plunger used to lock the tumbler reverse and backgear levers on Super 7 lathesCondition: New Application: ML-7R; Super 7 Category: New Old ...

Myford Part No: 75/1220 Screwed bush which fits into the tumbler reverse and backgear levers to retain the plungersCondition: New Application: ML7; ML-7R; Super...

Myford Part No. 86
Set of 4 faceplate clamps
Length: 2 1/2"
They are suitable for clamping work not only to the faceplate but also to the cross slide a...

Tumbler reverse lever assembly Comprising the following Myford Part No's: A1948/1 Tumbler Reverse Lever; A2005/2 Stud; A2008 Gear Studs; A3021 Plunger; A3025 Sp...

Leadscrew GuardMyford Part No: A4188/1Colour: Green - poor paintCondition: Unused Beeston factory stockApplication: ML7; Super 7; ML-7RCategory: New_Item...

30 tooth fibre Tumbler Gear Application: ML-7R; Super 7 Category: New_Item...

28 tooth fibre Tumbler Gear Application: ML-7R; Super 7 Category: New_Item...

Myford Part No. 1438Collet Nose Piece enables Myford MT2 Collets (11445) to be fitted directly into the headstock spindleCondition: 9/10Application: ML7; ML-7R;...

Myford 2 MT Collets fit directly into the spindle of all ML10, Speed 10, Diamond 10, ML7, ML7-R and Super 7 lathes, with spindle nose bored 2 MT and threaded 1....

Myford 2 MT Collets fit directly into the spindle of all ML10, Speed 10, Diamond 10, ML7, ML7-R and Super 7 lathes, with spindle nose bored 2 MT and threaded 1....

Myford Part No. A4736Colour: Grey - originalCondition: 9/10Application: ML7; ML-7R; Super 7Category: Used Item...

Thread Dial IndicatorMyford Part No.1419Fits to the right hand side of the apron by means of a stud inserted in the tapped hole provided. Graduated to show when...

60T Backgear Assembly
Myford Part No. A1993/1
Condition: Excellent little used - 9/10 to 10/10
Application: Super 7; ML7R
Category: Used item...

Leadscrew Handwheel
The Imperial leadscrew handwheel has 125 divisions each representing 0.001". This accessory can be used in order to obtain a fine feed to...

30T Gear - fits to the end of the headstock spindle
Myford Part No. A1995
Condition: Excellent used - 9/10
Application: Super 7; ML7R...

30T Gear - fits to the end of the headstock spindle
Myford Part No. A1995
Condition: Excellent used - 9/10
Application: Super 7; ML7R...

Backgear lever assembly
Comprising the following Myford Part No's:
A1949/1 Backgear Lever; A3021 Plunger; A3025 Spring; 75/1220 Screwed Bush; Knob & G...

L.H. Leadscrew Bracket Assembly
Myford Part No. 74/1134
Comes with A4725 Studs, nuts, washers and oil nipple
Colour: Grey
Condition: 10/10
Applic...

Myford Part No. 1437
For work which is too large for the standard 6 3/4" diameter faceplate. It has eight radial slots for the securing bolts for workpieces...

Myford Part No. A4736
Colour: Grey - original
Condition: 10/10 - may have been assembled
Application: ML7; ML-7R; Super 7
Category: New old stock...

30T Gear - fits to the end of the headstock spindle
Myford Part No. A1995
Condition: Good used - 8/10 to 9/10
Application: Super 7; ML7R...

Myford Tumbler Sleeve Gear Assembly
Myford Part No: A1998 (10351)
Condition: 9/10
Application: ML-7R; Super 7
Category: Used item...

Myford Part No: A3115 (11285/24)
24 tooth gear which fits to the tumbler sleeve gear on lathes fitted with a quick change gearbox
Condition: 9/10
Appl...

Myford Standard Faceplate
Size: 7 inch diameter
Fitting: Standard Myford spindle nose thread (1 1/8" - 12 tpi Whitworth form)
Colour: Green
Cond...

Headstock Spinde with No. 2 MT bore
Myford Part No: A1992
Condition: Good used - 8/10 to 9/10. There is a small ding on the register - Picture 2
Appli...