Centec Milling Machines
How to Order
Shipping & Dispatch
Keep up-to-date via e-mail!
Super 7 - Page 4
Massachusetts Lathe [MTC_700]
This is a vintage lathe made by the Massachusetts Tool Co. (later examples were sold under the name Goodell-Pratt)
Originally sold as " Precision Model Lathe...
Cone pulley [A3312_4U]
Countershaft cone pulleyMyford Part No: A3312Condition: 9/10Application: Super 7; ML7-RCategory: Used_Items ...
Series 7 Saddle Assembly [WGSA_3U]
Saddle Assembly to fit wide guide Series 7 lathes. Comes complete with front & rear saddle strips, gib strip, adjusting screws, eccentric clamp & fixing...
Change Gear Quadrant Assembly [CGQA_4]
Myford Part No. A4736Colour: Grey - originalCondition: 9/10Application: ML7; ML-7R; Super 7Category: Used_Items ...
Backgear Lever [A1949_1_4UG]
Backgear lever assemblyComprising the following Myford Part No's:A1949/1 Backgear Lever; A3021 Plunger; A3025 Spring; 75/1220 Screwed Bush; Knob & Grubscrew...
Thread Dial Indicator [MA1419_6]
Myford Part No.1419 Fits to the right hand side of the apron by means of a stud inserted in the tapped hole provided. Graduated to show when the leadscrew half ...
Thread Dial Indicator [MA1419_7N]
Myford Part No.1419Fits to the right hand side of the apron by means of a stud inserted in the tapped hole provided. Graduated to show when the leadscrew half n...
Leadscrew Guard [A4188_1_N]
Leadscrew GuardMyford Part No: A4188/1Colour: Green - poor paintCondition: Unused Beeston factory stockApplication: ML7; Super 7; ML-7RCategory: New_Item ...
Leadscrew Guard - Short [LSG_1U]
Leadscrew Guard - this guard is 25mm shorter than standard and is for use on lathes fitted with a gearbox where maximum saddle travel is required.Colour: GreenC...
30 Tooth Tumbler Gear [A2006_3N]
30 tooth fibre Tumbler Gear Application: ML-7R; Super 7 Category: New_Item...
28 Tooth Tumbler Gear [A2007_3N]
28 tooth fibre Tumbler Gear Application: ML-7R; Super 7 Category: New_Item...
Re-ground Bed & Saddle [S7RBA_1]
Myford factory (Beeston) re-ground bed and saddle assembly.This is a bed and saddle from a lathe that was going through the factory reconditioning process at th...
Super 7 Cross Slide Assembly [S7CSA_2]
Cross-slide assembly for a Super 7 lathe
Myford Part No's: A2020/1; A2068; A2069; A2149
This is a previously used cross slide which has been re-ground on ...
Myford Collet Nose Piece [MA1438_3U]
Myford Part No. 1438Collet Nose Piece enables Myford MT2 Collets (11445) to be fitted directly into the headstock spindleCondition: 9/10Application: ML7; ML-7R;...
Myford Collet Closing Tube [MA1439_3U]
Myford Part No. 1439 (2MT Collets) Collet Closing Tube comprises 11446 Extractor Sleeve and14367 Extractor. This device is intended for closing the collet to si...
Myford 7/32" Collet [MT27F32_1]
Myford 2 MT Collets fit directly into the spindle of all ML10, Speed 10, Diamond 10, ML7, ML7-R and Super 7 lathes, with spindle nose bored 2 MT and threaded 1....